Rack - Gun Rack - Wall Hung, Woodworking Plans

[ Pobierz całość w formacie PDF ]
How to Build a Wooden Gun Rack - Lee's Wood Projects
Lee's Wood Projects - How to Build a Wooden Gun Rack
Related Resources:
-
Lee's Site Map
-
Wood Projects
This beautiful hand crafted wooden gun rack is the
perfect way to display your favorite rifles. It is
made of walnut, and is designed to hang on the
wall and will add that special touch to your den or
trophy room. The two drawers provide storage for
shells and cleaning supplies. The shelf will
accommodate additional accessories. Keep your
guns neatly organized by building your own
wooden gun rack with the easy to follow
instructions below.
Click On Image to See Full Drawing
Technical Information for Building a Wooden Gun Rack
A. Materials List:
QUANTITY LETTER
NAME
SIZE
MATERIAL
1
A
Top
¾" x 4" x 21 ½"
Walnut
1
B
Bottom
¾" x 5" x 21 ½"
Walnut
1
C
Shelf
¾" x 5" x 21 ½"
Walnut
2
D
Sides
¾" x 5" x 27"
Walnut
1
E
Shelf Support
¾" x 3 ½" x 5"
Walnut
2
F
Drawer Fronts
¾" x 4 ¼" x 10 15/16"
Walnut
2
G
Drawer Backs
3/8" x 3 3/8" x 9 ½"
Walnut
4
H
Drawer Sides
3/8 " x 3 3/8" x 5"
Walnut
2
I
Drawer Bottoms
1/8" x 9 ¾" x 4 ½"
Hardboard
4
J
Drawer Guides
3/8" x 3/8" x 5"
Walnut
2
K
Drawer Pulls
¼" Diameter
Brass
B. Patterns:
1.
Scale top (A) to the drawing dimension size. This can easily be accomplished by measuring the print
out and dividing that size into the dimension size. This will give a multi-factor that can be used to
figure the enlargement size for the pattern. Most companies that do duplicating can make the
enlargement required for the pattern.
2.
Repeat step #1 for sides (D).
3.
Transfer the pattern enlargements onto poster board, and use a pair of scissors to cut out the
patterns.
C. Cutting Procedures:
1 of 3
05/05/2007 2:21 PM
How to Build a Wooden Gun Rack - Lee's Wood Projects
1.
Use a
jointer
to joint one edge of all lumber.
2.
Use a
planer
to plane all lumber to required thicknesses.
3.
Use a
radial arm saw
to cut all lumber to required lengths.
4.
Use a table saw to rip all lumber to required widths.
5.
Trace the pattern for top (A) and sides (D) onto the lumber and cut out the shapes with a
band saw
.
6.
Use a
spindle sander
to sand the shapes for top (A) and sides (D).
7.
On the inside of sides (D) measure 2 5/16" from the bottom of each side. Use a radial arm saw to cut
dado joints for the drawer guides (J) 3/8" wide x 3/16" deep in each side.
8.
Measure 1 9/16" up from the bottom of the self support (E), and use a radial arm saw to cut dado
joints for the drawer guides (J) 3/8" wide x 3/16" deep on both sides of the self support.
9.
On the outside of each drawer side (H) measure 1 ½" up form the bottom of the drawer side, and use
a table saw cut dado grooves 13/32" wide x 3/16" deep to accommodate the drawer guides.
10.
On the inside of the drawer fronts (F), cut 3/8" x 3/8" rabbet joints at the top, bottom and sides of
each drawer.
11.
On the inside of drawer front (F), back (G), and sides (H), cut 1/8" x 1/8" deep dado joints 1/8"
from the bottom edges of each side and back to accommodate the drawer bottoms.
12.
Route edges of drawer fronts (F) with a 5/8" Roman-Ogee Bit.
13.
Drill a 1/8" hole through the center face of each drawer front (F) to accommodate the screws for the
drawer pulls (K). Also bevel the holes on the inside of the drawer fronts so that the flathead screws
will fit flush.
D. Sanding Procedures:
1.
Rough sand all parts with an orbital sander and 80 grit sandpaper.
2.
Intermediate sand all parts with an orbital sander and 120 grit sandpaper.
3.
Rough and intermediate, sanding should be completed before assembly procedure.
4.
Finish sand all parts with an orbital sander and 220 grit sandpaper
after the assembly procedure
.
5.
Hand sand all edges, details, with 220 grit sandpaper just
prior to the finish procedure
.
E. Assembly Procedures:
1.
Measure 1" down from the top of sides (D). Apply wood glue on both ends of top (A) and align the
top between the sides at the 1" marks. Also be sure the top is flush with the back of each side. Using
a nail gun with 2" nails, secure the top to the sides.
2.
Glue and nail bottom (B) flush with the bottom of sides (D).
3.
Glue and nail shelf (C) 3 ½" up from bottom (B).
Note:
Make sure that the shelf and the bottom are
perfectly parallel.
4.
Glue and nail the shelf support (E) in place.
5.
Glue drawer guides (J) in the sides (D) and the self support (E).
6.
Position the drawer bottom (I) in the dado grooves of the drawer front (F), drawer back (G), and the
drawer sides (H). Glue and nail drawer together with 1" nails. Repeat procedure for the other
drawer.
7.
Attach drawer pulls (K).
Note:
Drawer pulls should be attached after the finish procedure.
8.
Apply wax on the drawer guides (J) and in the dado grooves of the drawer sides (H). This will allow
the drawers to slide more freely.
9.
Place drawers in the gun rack assembly.
F. Finish Procedures:
1.
Use plastic wood dough to fill all holes, cracks and imperfections.
2.
Hand sand all edges with 220 grit sandpaper.
3.
If stain is desired, apply with a brush and allow to dry penetrate for 5-10 minutes, then remove with
a clean rag.
4.
Allow stain to dry 6 hours and then repeat with a second coat.
2 of 3
05/05/2007 2:21 PM
How to Build a Wooden Gun Rack - Lee's Wood Projects
5.
Apply a clear finish coat such as Varathane, Polyurethane, etc. using a pure-bristle brush. Allow to
dry 12 hours.
6.
Lightly hand sand finish with 220 grit sandpaper.
7.
Apply second coat of clear finish.
8.
If third or fourth coats are desired, be sure to allow the finish to dry properly then lightly hand sand
with 220 grit sandpaper between coats.
9.
Allow final coat to dry 24 hours before using your wooden gun rack.
Congratulations, your wooden gun rack is finished and ready to display your rifles.
Related Woodworking Plans:
Wooden Quilt Rack Plan
Wooden Spice Rack
Lee's Wood Projects
|
Woodworking Projects
|
Ask Lee
|
Woodshop
|
Resources
|
Site Map
Copyright © 2005-2007 Leeswoodprojects.com
3 of 3
05/05/2007 2:21 PM
[ Pobierz całość w formacie PDF ]

  • zanotowane.pl
  • doc.pisz.pl
  • pdf.pisz.pl
  • tejsza.htw.pl

    •